most software todos done

TODO

@@ -1,11 +1,11 @@
-- entprellung des tasters
 - limiter nur bei brownout
-- auto-aus nach 2 stunden
-- rasten verändern (2.5°C)
 - gehäusefüße dran
-- temperaturmaximum evtl reduzieren (80°C?) oderauchnicht
+- hochglanzpolieren
-- beide temperaturmaxima gleich
+done - entprellung des tasters
-- hochlganzpolieren
+done - auto-aus nach 2 stunden
+done - rasten verändern (2.5°C)
+done - temperaturmaximum evtl reduzieren (80°C?) oderauchnicht
+done - beide temperaturmaxima gleich
 
 "Langzeittests"
 - maximale temperatur

firmware/cup.c

@@ -13,8 +13,9 @@
 
 #define TIMEOUT 51 /* 2 seconds */
 
-const uint16_t LED_GREEN_TEMP = 300;
+#define LED_GREEN_TEMP 300
-const uint16_t LED_RED_TEMP = 1000;
+//#define LED_RED_TEMP 1000
+#define LED_RED_TEMP 800
 
 #define TARGET_TEMP_MIN 300
 #define TARGET_TEMP_MAX 1520
@@ -36,13 +37,20 @@ uint8_t heat_power = 0; // requested heating power; 0..255
 uint8_t input_state = 0;
 uint8_t dev_state = 0; // whether the device is on or off
 
+#define TOGGLE_TIMEOUT 5
 #define TEN_SECONDS 256
+#define ONE_MINUTE 1536
+#define ONE_HOUR 92160
+
+uint8_t toggle_timeout = 0;
+
 uint16_t startup = TEN_SECONDS;
 
 uint8_t eeprom_write = 0;
-#define ONE_MINUTE 1536
 uint16_t eeprom_clk = ONE_MINUTE;
 
+uint32_t shutdown = 2 * (uint32_t) ONE_HOUR;
+
 /* gray code to change lookup table, index is old state .. new state */
 int8_t state_change[16] = {0, 1, -1, 0,  -1, 0, 0, 1,  1, 0, 0, -1,  0, -1, 1, 0};
 //int8_t state_change[16] = {0, -1, 1, 0,  1, 0, 0, -1,  -1, 0, 0, 1,  0, 1, -1, 0};
@@ -51,6 +59,7 @@ int8_t state_change[16] = {0, 1, -1, 0,  -1, 0, 0, 1,  1, 0, 0, -1,  0, -1, 1, 0
 ISR(TIM1_OVF_vect)
 {
 	/* timeout for displaying target temperature */
+	if(toggle_timeout) {toggle_timeout--;}
 	if(setting_timeout) {setting_timeout--;}
 	if(startup) {startup--;}
 	if(eeprom_clk) {eeprom_clk--;}
@@ -59,6 +68,8 @@ ISR(TIM1_OVF_vect)
 		eeprom_write = 1;
 		eeprom_clk = ONE_MINUTE;
 	}
+	if(shutdown) {shutdown--;}
+	else {dev_state = 0;}
 	
 	/* incremtening softpwm, toggling output if needed */
 	heat_pwm++;
@@ -92,20 +103,24 @@ ISR(PCINT0_vect)
 	uint8_t diff = new_state ^ input_state;
 	if(!diff) {return;}
 	
-	if(diff & (1 << (TAST_PIN - 1)) && new_state & (1 << (TAST_PIN - 1)))
+	if(!toggle_timeout && diff & (1 << (TAST_PIN - 1)) && new_state & (1 << (TAST_PIN - 1)))
 	{
 		dev_state = !dev_state;
+		toggle_timeout = TOGGLE_TIMEOUT;
 	}
 	
 	int8_t change = state_change[((input_state & 3) << 2) | (new_state & 3)];
 	if(change)
 	{
-		target += change * 10; // 1 celsius per step
+		target += change * 6;//0.6K * 4 per step       10; // 1 celsius per step
-		if(target < TARGET_TEMP_MIN) {target = TARGET_TEMP_MIN;}
+		//if(target < TARGET_TEMP_MIN) {target = TARGET_TEMP_MIN;}
-		else if(target > TARGET_TEMP_MAX) {target = TARGET_TEMP_MAX;}
+		//else if(target > TARGET_TEMP_MAX) {target = TARGET_TEMP_MAX;}
+		if(target < LED_GREEN_TEMP) {target = LED_GREEN_TEMP;}
+		else if(target > LED_RED_TEMP) {target = LED_RED_TEMP;}
 		setting_timeout = TIMEOUT;
 	}
 	
+	shutdown = 2 * (uint32_t) ONE_HOUR;
 	input_state = new_state;
 }